aluminum electrolytic capacitors u 1 z 2 r 3 1 4 c 5 1 6 0 7 0 8 m 9 c 10 l 11 1 12 g 13 b 14 configuration taping code capacitance tolerance ( 20%) rated capacitance (10 f) rated voltage (16v) series name type plastic platform series capacitance voltage (c : 16v) lot no. positive negative x2 10c zr 0.3 max. 3.90 +0.05 0.2 d 0.5 b 0.2 c 0.2 0.5 max. a 0.2 a 0.2 e 0.5 ~ 0.8 zr series 3.95mml max. chip type chip type type numbering system (example : 16v 10 f) specifications zr zs dimensions 0.1 0.22 0.33 0.47 1 2.2 3.3 4.7 10 22 33 47 100 220 0r1 r22 r33 r47 010 2r2 3r3 4r7 100 220 330 470 101 221 4 4 5 6.3 28 33 56 96 4 5 5 6.3 28 37 45 70 5 5 6.3 33 41 52 4 5 6.3 6.3 23 37 49 58 4 5 6.3 6.3 16 27 42 52 4 5 6.3 18 29 46 4 4 4 4 4 4 4 5 6.3 1.0 2.0 2.8 4.0 8.4 13 17 20 33 rated ripple 4 0g 6.3 0j 10 1a 16 1c 25 1e 35 1v 50 1h v code rated ripple (marms) at 85? 120hz d a b c e 4 1.8 4.3 4.3 1.0 5 2.1 5.3 5.3 1.3 6.3 2.4 6.6 6.6 2.2 (mm) cap. ( f) smaller smaller stability at low temperature resistance to soldering heat z?0? / z+20? category temperature range rated voltage range rated capacitance range capacitance tolerance leakage current tan marking performance characteristics item 40 ~ +85? 4 ~ 50v 0.1 ~ 220 f 20% at 120hz, 20? after 2 minutes' application of rated voltage , leakage current is not more than 0.01 cv or 3 ( a) , whichever is greater. rated voltage (v) rated voltage (v) tan ( max.) 4 0.50 4 7 15 6.3 0.30 6.3 4 8 10 0.24 10 3 8 16 0.19 16 2 4 25 0.16 25 2 4 35 0.14 35 2 3 50 0.14 50 2 3 120hz 20? 120hz impedance ratio zt / z20 (max.) z?5? / z+20? after storing the capacitors under no load at 85? for 1000 hours, and after performing voltage treatment based on jis c 5101-4 clause 4.1 at 20?, they will meet the specified value for endurance characteristics listed above. the capacitors shall be kept on the hot plate maintained at 250? for 30 seconds. after removing from the hot plate and restored at room temperature, they meet the characteristic requirements listed at right. black print on the case top. shelf life endurance after 1000 hours' application of rated voltage at 85?, capacitors meet the characteristic requirements listed at right. capacitance change leakage current tan within 10% of initial value initial specified value or less initial specified value or less capacitance change leakage current tan within 30% of initial value 300% or less of initial specified value initial specified value or less frequency coefficient of rated ripple current coefficient frequency 50 hz 120 hz 300 hz 1 khz 10 khz~ 0.70 1.00 1.17 1.36 1.50 chip type with 3.95mmlmax height. designed for surface mounting on high density pc board. applicable to automatic mounting machine using carrier tape. adapted to the rohs directive (2002/95/ec). zd voltage v 4 6.3 10 16 25 35 50 code g j a c e v h case size d (mm) taping specifications are given in page 24. recommended land size are given in page 25. please contact us for the soldering by reflow. please refer to page 3 for the minimum order quantity. cat.8100v
|
